Personnel

One certified electrician

 

 

 

 

Safety

WARNING

warning

Before installing the charging station, refer to safety instructions.

WARNING

warning

Risk of Electrocution

There is a risk of electric shock. Do not alter, relocate, drill, or remove any component without consulting with an EV Meter certified team.

WARNING

warning

Local Electrical Regulations

All installation actions must be done by a certified electrician and according to the local regulations.

 

 

 

What is in the Box

  • Installation Manual
  • Warranty
  • 10 × M4 Allen screws
  • 2 × screws
  • Charging station
  • Front frame
What is in the Box

 

 

Tools and Equipment

  • Flat bit
  • Level
  • Drill
  • Hammer
  • Voltmeter

 

 

 

Materials

  • M10 Stainless Steel bolts and nuts
  • Two flexible 3×8 AWG Cables
  • Dowels
  • Charging Station Kit

 

 

 

Preparations

NOTICE

notice

Kit Unboxing

The kit unboxing is to be performed only by a certified electrician followed by a visual check for any damaged/ broken parts. In case of any damage, contact EV Meter support.

    1. Unbox the charging station kit.
    2. Make sure two circuit breakers and two TBs are installed in the electrical panel, according to the following table:

      Connection type

      Max Power output

      Circuit breaker

      1 Phase or 2 Phase

      6-12 kW

      1×50 A

        1. Insert each cable from the circuit brakers into a flexible 3×8 AWG cable. Make sure the cables are long enough to reach the charging station.
        2. Turn off the charger power using the circuit breakers.
        3. Using a voltmeter or any equivalent device, make sure that all the power to the charger is turned off.

          NOTICE

          notice

          To provide quick power off, in case of emergency or maintenance, install an emergency switch, according to the local regulations and the power input to the charging station.

          EV Meter recommend installing an emergency switch specifically for the charging station, next to the charging station.

           

           

           

          Installation Overview

          CAUTION

          caution

          Installation Conditions

          The installation must be performed in dry conditions.

          The installation process includes the following steps:

          1. Charger Wall Mounting Bracket Installation
          2. Charger Mounting
          3. Electrical Panel Power Cable Connection.
          4. Charger Assembly

           

           

           

          Charger Wall Mounting Bracket Installation

            1. Open the front cover of the charger.
            2. Disconnect the harness connected between the charger and the front cover.
            3. Remove the front cover from the charger.
            4. Remove the wall mounting bracket from the back of the charger.
            5. Place the wall mounting bracket on the wall.
            6. Using a drill, drill four holes, according to the holes placement in the charger’s wall mounting bracket.
            7. Using a hammer, hammer four dowels into the holes.
            8. Using a screwdriver, screw four M10 screws, and nuts, secure the wall mounting bracket.
            9. The wall mounting bracket is attached to the wall.
              Wall Bracket

               

               

              Charger Mounting

                1. Align the sockets on the charger with the anchors on the charger wall mounting bracket.
                2. Place the charger on the wall mounting bracket.
                3. Using a Phillips screwdriver, install two Phillips screws on the bottom of the charger, to secure the charger to the charger wall mounting bracket.
                  Charger Mounting

                   

                   

                  Electrical Panel Power Cable Connection

                  WARNING

                  warning

                  Risk of Fire

                  There is a risk of fire. Do not alter, relocate, drill, or remove any component without consulting with an EV Meter certified team.

                  CAUTION

                  caution

                  Cable Placement

                  Make sure the cable is not placed in the way of any pedestrians, vehicles, or objects.

                    1. Loosen the two cable glands on the bottom of the charger.
                    2. Insert the 3×8 AWG cables trough the cable glands.
                    3. Using a flat bit, release the screws of the charger TBs.
                    4. Connect the L1, L2/N, GND cables to the charger TBs according to the following diagram.
                    5. Using Flat bit tighten the charger TBs screws to secure the cables.
                    6. Using Allen bits, release the Allen screws of the grounding branch point.
                    7. Connect the grounding cables to the grounding branch point.
                    8. Using Allen bits, tighten the Allen screws to secure the cables.
                    9. tighten the two cable glands on the bottom of the charger.
                      Electrical Connectors

                       

                       

                      Charger Assembly

                        1. Connect the charger cover’s harness to the charger harness according to the following figure.
                        3. Place the charger cover on the charger.
                        4. make sure the charger cover fits in the charger’s plug holders.
                        5. Using an Allen bit, screw 10 M4×15 Allen screws to secure the charger cover to the charger.
                        6. By hand force, install the front frame.
                          Charger Assembly